In this guide, we will show you how to bypass the FRP on the Xiaomi Redmi Note 10 5G smartphone. As we know, the device came out of the box with Android 11.0 under MIUI 12 powered by the latest MT6833 Dimensity 700 5G chipset.

If you are someone who has lost the Google account information to access your device after a factory reset, then this guide is for you. FRP stands for Factory Reset Protection that protects your device and information, including screen locks and data encryptions. It is enabled automatically when you add the Google account on your device and will be disabled if the Google account is removed from the device prior to the Factory Data Reset.

Also Read

Download Google Camera for Redmi Note 10 5G | GCam APK

Redmi Note 10 5G Device Overview:

The Redmi Note 10 5G features a 6.5-inch IPS LCD panel with a resolution of 1080 x 2400 pixels and an aspect ratio of 20:9. It is a high refresh rate panel with a 90Hz refresh rate and is protected by Corning Gorilla Glass 3. Under the hood, we have the MediaTek Dimensity 700 5G chip built on a 7nm manufacturing process. It is an octa-core processor with two Cortex-A76 cores clocked at 2.2 GHz and six Cortex-A55 cores clocked at 2.0 GHz. For handling the graphics-intensive tasks, we have the Mali-G57 MC2.

Coming to the optics, we get a triple camera setup at the rear and a single camera at the front. The triple rear camera consists of a 48MP primary sensor paired with an f/1.8 lens, a 2MP macro sensor paired with an f/2.4 lens, and a 2MP depth sensor paired with an f/2.4 lens. At the front, we get an 8MP sensor paired with an f/2.0 lens. Both the front and the rear camera setup is limited to 1080p video recording.

The Redmi Note 10 5G has six storage options: 64GB internal storage + 4GB RAM, 128GB internal storage + 4GB RAM, 128GB internal storage + 6GB RAM, 128GB internal storage + 8GB RAM, 256GB internal storage + 4GB RAM, and 256GB internal storage + 8GB RAM.

In terms of communications, we get Wi-Fi 802.11 a/b/g/n/ac, Bluetooth 5.1, GPS, NFC, Infrared port, FM radio, and USB Type-C 2.0. And in terms of sensors, we get a side-mounted fingerprint sensor, accelerometer, gyro, proximity, and compass. Powering it all is a 5000 mAh battery that supports 18W fast charging.

Pre-Requirements:

  • This guide works only on Redmi Note 10 5G. Don’t try it on other devices.
  • You need a Windows PC or Laptop with a working USB cable.
  • Download the SP Flash Tool for bypassing via 1st method.
  • For Scatter File: Download Redmi Note 10 5G Firmware Flash File
  • Download MTK VCOM Drivers and install them on your computer.
  • Download and install the Android USB Drivers on your PC.
  • Make sure to charge your device to at least 60% before following this step.
  • Take a full backup of your device’s internal data.

After following all the pre-requirements mentioned above, now you can follow the flashing steps carefully:

Steps to ByPass FRP lock verification on Redmi Note 10 5G

First, you need to disable SLA Authentication

Warning!

Method 1: Using SP Flash Tool

Follow these instructions carefully to remove the FRP lock on the Redmi Note 10 5G MediaTek-powered device via the SP Flash tool.

You can watch our video guide to remove the FRP lock on Redmi Note 10 5G.

Method 2: Using Infinity CM2

Follow these instructions to bypass FRP lock on Redmi Note 10 5G via Infinity CM2:

Method 3: Using Miracle Box Tool

Follow these instructions to bypass FRP lock on Redmi Note 10 5G via Miracle Box Tool

We hope that you’ve successfully bypassed the FRP Lock on your Redmi Note 10 5G. If you’ve any issues or queries regarding this, feel free to write them down in the comments below.

Advertisement